Przem's Phase Linear 700 Series II White Oak Conversion

[derek92994]

Was out loading tubing till 10 last night. Gotta haul it to the rig now.... man is it busy this week..

Hang in there Lee, I'm sure you will do it with ease, time flies hey.

 

[derek92994]

What Happened to Skynyrd? no posts in his thread for a while.

 

[laatsch55]

Don't know...good question...

 

[Skynyrd77]

What Happened to Skynyrd? no posts in his thread for a while.

Hey d2. I'm back. Just had a lot of shit on my plate. I think I got it mostly taken care of. So fingers crossed. I won't come up missing again lmao. How have you been doing??

 

[derek92994]

Hey d2. I'm back. Just had a lot of shit on my plate. I think I got it mostly taken care of. So fingers crossed. I won't come up missing again lmao. How have you been doing??

Doing better than the last few weeks, keeping busy. Can't complain I guess =).

 

[Skynyrd77]

Doing better than the last few weeks, keeping busy. Can't complain I guess =).

Thats about all we can ask for lol. It's been a struggle here but I try not to let it get me down. I just need my speaks back so I can work Jessica a bit..

 

[laatsch55]

When trying to drill holes in chassis' I use a transfer punch to start. The layout is critical when using countersunk screws like those needed in this IEC plug. The transfer punch leaves a shallow depression, but not really enough to go hogwild with a hand drill. So, I start with a 1/16" bit in a pin vise and deepen the starter hole a bit more to lessen the "bit walkin" that would really screw up this nice chassis....

 

[laatsch55]

Voila'.....

 

[Gepetto]

Voila'.....

Nice job Lee...

 

[laatsch55]

Thanks Joe....any ideas for a bulkhead connector that would fit the old AC in hole??

 

[Gepetto]

Thanks Joe....any ideas for a bulkhead connector that would fit the old AC in hole??

You mean a hole plug Lee?

 

[laatsch55]

For the 120 fan voltage.....how about an RCA jack???

 

[Lazarus Short]

For the 120 fan voltage.....how about an RCA jack???

If you do, sooner or later you will plug a signal cable into it by mistake. I know I would... Use an automotive connector - they don't know [or care] if its 12 VDC or 120 VAC.

 

[Gepetto]

For the 120 fan voltage.....how about an RCA jack???

Lee you don't want to make a widow maker...

Wire in a 6" long wire pigtail with female 5-15R on the end of it to plug the original fan plug into. Use the original Heyco clamp to strain relieve the pigtail into the chassis hole.

Think safety here.

 

[laatsch55]

.Nor a bad idea Joe, BNC?? My original idea of an amphenol 3057 connector is too large....

 

[Gepetto]

.Nor a bad idea Joe, BNC?? My original idea of an amphenol 3057 connector is too large....

Buy something like this, cut the unused end off it and use the 5-15R through the original Heyco strain relief. Neat and safe.

 

[laatsch55]

Likee so....

 

[laatsch55]

Buy something like this, cut the unused end off it and use the 5-15R through the original Heyco strain relief. Neat and safe.

View attachment 15484

Ok Sir Joe...

 

[pennysdad]

I have a Pioneer D-23 x-over and am considering it BD....

http://www.ebay.com.au/itm/Pioneer-...age_Electronics_R2&hash=item3ce4fd62f0&_uhb=1

 

[laatsch55]

That's the one BD..