Ben's (BubbaH's) Phase Linear 400 WOPL conversion

Hell, that explains it, hadn't opened the attachments yet, got em downloaded to the appropriate folders now. Thannks for your patience Sir Joe!
 
Don't know about other folks, but the solder cups have to be handled with mini-needle nose. Scotch blue painter's tape holds them well enough that you do not need any weight on the silkscreen side after you flop them back over to SOLDER THEM TO THE SILKSCREEN side....
 

Attachments

  • SAM_0941.jpg
    SAM_0941.jpg
    86.9 KB · Views: 44
  • SAM_0940.jpg
    SAM_0940.jpg
    100.1 KB · Views: 48
  • SAM_0939.jpg
    SAM_0939.jpg
    82.3 KB · Views: 42
The experience gained from soldering the PEM standoffs is extremely helpful when trying to manage the meniscus on something this small. The lack of an extremely large copper plane also helps, heats up very fast...
 

Attachments

  • SAM_0942.jpg
    SAM_0942.jpg
    93.4 KB · Views: 42
Navo's PEM standoff holders...
 

Attachments

  • SAM_0943.jpg
    SAM_0943.jpg
    91.9 KB · Views: 50
Standoffs in.....
 

Attachments

  • SAM_0945.jpg
    SAM_0945.jpg
    75 KB · Views: 45
  • SAM_0944.jpg
    SAM_0944.jpg
    91 KB · Views: 38
Left board done..
 

Attachments

  • SAM_0946.jpg
    SAM_0946.jpg
    98.4 KB · Views: 48
Rockin and rollin on another lee
if ya need to borrow my Christmas Ox to get it to Canada lmk! Prob a better delivery service than fedex or ups.... Your gonna love it ben.
 
Right board done.
 

Attachments

  • SAM_0948.jpg
    SAM_0948.jpg
    98 KB · Views: 39
  • SAM_0947.jpg
    SAM_0947.jpg
    99.4 KB · Views: 40
Thanks for showing the build- I'm planning on this upgrade at the turn of the year after the holiday bills are paid. Another snag is that I just obligated myself to pay for a PL 4000/II preamp- a beautiful one from the original owner, and in stellar condition (hopefully no cracked solder joints between mother and daughter boards).

So- my question is this: since the transistors have to poke through the back of the cabinet into these boards, is there some kind of alignment issue that I need to be aware of? And is this alignment issue easily resolved? I saw the post on the PEM standoff holders- is this what is used to hold these things in place for soldering? (My naïveté is showing, isn't it?)

This kit doesn't look to be beyond my ability to execute, but sometimes there are some little tricks- just preparing myself...

Two and a half other questions:
  • This is a good time to convert from quasi to full comp, correct? (WO sells the semiconductors, right?)
  • I have to alter the driver board to accommodate the FC transistor upgrade (parts for both builds were included with the driver board kit).
 
So- since the transistors have to poke into these boards, is there some kind of alignment issue? And is this alignment issue easily resolved?

Just make sure your poker is lined up with the hole before you stick it in. :shaking: :tongue5: :shaking:
 
The chassis were pretty consistent. No issues to this point with any 400 application. The only alignment issue has been with the heatsinks on the 700's. Some 700 heatsinks need the mounting holes taken from a"C" to a "B" drill.
The 400 backplane board kits are Quasi/full comp with a few component changes and everything is included to go either way , except the outputs.
The PEM standoff clamps are not necessary and are a product of our wonderful NavLinears mind and 3D copier. Joe uses a wooden dowel....
The driver board has to be
populated in FC mode, yes...
 
The chassis were pretty consistent. No issues to this point with any 400 application. The only alignment issue has been with the heatsinks on the 700's. Some 700 heatsinks need the mounting holes taken from a"C" to a "B" drill.
The 400 backplane board kits are Quasi/full comp with a few component changes and everything is included to go either way , except the outputs.
The PEM standoff clamps are not necessary and are a product of our wonderful NavLinears mind and 3D copier. Joe uses a wooden dowel....
The driver board has to be
populated in FC mode, yes...

Awritie then- as soon as my Visa card is back down to zero...

Thanks!

BTW- What's with all you guys? I've never had replies to my answers this fast with any other forum! Go play a record! Get your noses away from your screens!
 
My computer is in my mancave....doing company paperwork , rattling the walls with some Prometheus and watching the Broncos-Miami game...and viewing the forum occaisonally...
 
My computer is in my mancave....doing company paperwork , rattling the walls with some Prometheus and watching the Broncos-Miami game...and viewing the forum occaisonally...

Good Man....Priorities :blob8:
 
That's a rather subdued lol for someone getting the ass cut on tomorrow....
 
Back
Top