Ultra-high performance low-buck phono preamp (DIY project!)

laatsch55

Administrator,
Staff member
Joined
Jan 14, 2011
Messages
74,124
Location
Gillette, Wyo.
Tagline
Halfbiass...Electron Herder and Backass Woof
#41
What she actually said was " My, what big nuts he has"....
Yeah, she's a trip, definitely a keeper..
 

J!m

Veteran and General Yakker
Joined
Dec 24, 2019
Messages
9,246
Location
Connecticut
Tagline
BOT
#45
Today my enclosure came in so I started roughing it out.

it has more RCA holes than I need, so I adapted two for turntable grounds.

3266EC13-85ED-4FEA-B920-767648A7AB9F.jpeg 8A8E8A59-4FAF-4B55-91CB-7D7266D348C1.jpeg

Since they didn’t fit, I made some adapter bushings for them.
1FC30552-E084-4FDE-A7B4-A72DBF7E4FC0.jpeg 5A2720D1-80E9-44C5-84B2-9C193C479659.jpeg D0301F66-9F57-4952-91D0-A77B89EFCCCF.jpeg 3D612A18-0367-4191-AA03-99BFD7770771.jpeg

Put some clear coat on them after I verified they fit.
F566AA1A-56DD-45F3-8E23-E8A007209CCC.jpeg 62959195-0B4D-4D43-A963-246E3977FA6B.jpeg

Had to make an adapter for power. It’s set up to have everything in one box but I’m running the power supply remote. Filter board is in here but what started as an adapter plate turned into a steel box to control RF.
7D745FC5-8C13-43FE-9FA7-FED1C9D719D4.jpeg 86B0FC16-3FDF-46FC-AD56-15B3A01504C7.jpeg
 
Last edited:

J!m

Veteran and General Yakker
Joined
Dec 24, 2019
Messages
9,246
Location
Connecticut
Tagline
BOT
#46
73B17DD5-0DA1-4284-854B-7A6183A044EF.jpeg

I had this bit sticking out I figured I’d extend to the front to isolate the power but the board is so small it evolved into an enclosure.
00F6E1F5-E4C1-46BD-9A22-2B209B14B565.jpeg 0EABF578-F311-459B-88AB-C5B42DFAE186.jpeg

I blasted and painted it. Now to work out the front panel…
 

mlucitt

Veteran and General Yakker
Joined
Jun 24, 2011
Messages
3,339
Location
Jacksonville, FL
#47
Nice work on the bushings and the enclosure. Don't forget to drive a Dremel around and inside the phono grounding hole, that anodizing is a fairly good insulator and may act as a capacitor dielectric!
 

J!m

Veteran and General Yakker
Joined
Dec 24, 2019
Messages
9,246
Location
Connecticut
Tagline
BOT
#57
Believe it or not, it’s a cheap switching power supply. And although apparently not necessary, I am mounting it external.

The small board in the steel box is a filter board.
 

J!m

Veteran and General Yakker
Joined
Dec 24, 2019
Messages
9,246
Location
Connecticut
Tagline
BOT
#58
Minor progress today.

Some of the caps are 1% tolerance, and they are back ordered u til December. I found nearly identical ( brand etc) at 2% tolerance because I figured they would be the only thing I’d be waiting on.

Today I measured them with my Fluke (not the best tool for the job) and they all measure within 1% of value. Three were right on.

So I took two that were right on and put them in the MM board, so it would be finished. I also added the cartridge “loading” caps. So that board is now done. I already had the output wires in place but added the input wires today too. Small victory as I placed another Mouser order…

The muting relays are also back ordered until December. Two “replacement” relays are well spec’d but larger form factor. Today I found the SMD version of the exact relay and orders those. I’ll have to straighten the legs out and through hole solder them. Wish I figured that out a couple weeks ago…

20D013DD-E173-4917-831D-D281F9866970.jpeg
 

J!m

Veteran and General Yakker
Joined
Dec 24, 2019
Messages
9,246
Location
Connecticut
Tagline
BOT
#60
Another update.

Again with the wrong relays… these are/were the same relay, just with bent legs for SM. I straightened them carefully and found:

They don’t fit.

After three failed attempts to get a fucking pair of relays, I MADE them fit.
9088B0A8-A835-45FC-BAD2-B54C44D6D2CF.jpeg E3E0E953-8B2F-46FB-B163-221B44D3DC9F.jpeg

One side I got through the board; the other side is surface mount. I flowed enough solder to see it in the holes on the other side so, DONE.
 
Top