Yeah, I am the cut man...
Skynyrd77's Thank Godamighty , Finally My Own WOPL Build Thread!!
- Thread starter laatsch55
- Start date
Yeah, I am the cut man...
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
OK, clips at 387 into 4 ohms with rail voltage at 79.7.... What's up with that Joe....
You thought you would never hit the SOA protection Lee?
Are you looking at your 79.7V with the scope or are you looking at the RMS value with a DMM.
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
And a legendary one at that.......around here anyway...
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
The Fluke 179, set on DC volts...
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
So, you're saying the 1304 and 5's are in play...?
That is giving you an RMS reading Lee. It may be drooping terribly on a cycle by cycle basis. You should check.
Can very well be Lee...
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Ok, how do I set up the scope??
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Should monitor incoming mains then too...
Synch channel 1 on the output signal and then put channel 2 on the B+ test point on the backplane board and look at it at the point that the signal starts to clip.
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
This is a stock 700 Joe....
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
With RCA 410's and XPL-909's throughout....
Skynyrd77
Veteran and General Yakker
Hey look I got a thread!!!
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Um....YEP....
Skynyrd77
Veteran and General Yakker
And in SKYNYRD English that translates to
FUCK YES!! FINALLY I HAVE A THREAD FOR A 1000 WOPL!!
FUCK YES!! FINALLY I HAVE A THREAD FOR A 1000 WOPL!!
Ooops thought this was a converted one. Then just look at the B+ collector rail on the channel you are measuring. And don't blow it up.
Northwinds
Veteran and General Yakker
- Joined
- Mar 18, 2013
- Messages
- 7,571
- Location
- Coventry, CT
- Tagline
- Fondler errrr... fan of all Nav's avatars
I love where this is heading hehehehehehehee
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
With the scope in DC coupling? And don't blow it up??? Dude that's why we are doing this, to see where it goes south at 4 ohms...
- Joined
- Jan 14, 2011
- Messages
- 75,632
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
And we have 10 amp rail fuses and a 15 amp mains in fuse installed....