Glen's 700 series II build
- Thread starter grapplesaw
- Start date
- Joined
- Jan 14, 2011
- Messages
- 74,912
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
I hope everyone had a good thanks giving regardless of the weeks craziness.
I have 7 kids and 14 grandkids on both the east and west coast. 5 kids and all grandkids were born in the good old USA. We had lots of conversation with them this week. We usually go to Oregon for Thanks giving but it did not workout this year.
So the week was a bust on this little project.
Got the Pl14-20 put together tonight. I will work on finishing backplates this weekend if all goes well
Post photos tomorrow with some added features.
Night all
I have 7 kids and 14 grandkids on both the east and west coast. 5 kids and all grandkids were born in the good old USA. We had lots of conversation with them this week. We usually go to Oregon for Thanks giving but it did not workout this year.
So the week was a bust on this little project.
Got the Pl14-20 put together tonight. I will work on finishing backplates this weekend if all goes well
Post photos tomorrow with some added features.
Night all
This looks complete now
I added some heat sinks to Q1 and Q2
Any one have preference for cleaning product to remove excess Soldering Rosin from Board?
90% Isopropyl alcohol.
D13L/R cannot be installed for a full comp application.
View attachment 17678 View attachment 17679 View attachment 17680
I added some heat sinks to Q1 and Q2
Any one have preference for cleaning product to remove excess Soldering Rosin from Board?
90% Isopropyl alcohol.
D13L/R cannot be installed for a full comp application.
View attachment 17678 View attachment 17679 View attachment 17680
D13L/R cannot be installed for a full comp application.
Mod to Backplate
Here is the nearly completed mod for Series two
After narrowing the boards with a router on a router table I filed and sanded the edges to very fine finish .I looked for any copper trace jumping between layers before coating the edges with some 5 minute Epoxy. I double coated then to yield +/- 1/32 of coating.
The boards now have only about .005 -.010 clear
I then added a length of 1 mi Kapton tape to the frame ( anyone think I should double or triple thickness please let me know)
So now ready to put together
Thanks to Joe for all his tips and Eagle eyes (I missed omitting some Diodes) on this procedure I can now move forward.
Here is the nearly completed mod for Series two
After narrowing the boards with a router on a router table I filed and sanded the edges to very fine finish .I looked for any copper trace jumping between layers before coating the edges with some 5 minute Epoxy. I double coated then to yield +/- 1/32 of coating.
The boards now have only about .005 -.010 clear
I then added a length of 1 mi Kapton tape to the frame ( anyone think I should double or triple thickness please let me know)
So now ready to put together
Thanks to Joe for all his tips and Eagle eyes (I missed omitting some Diodes) on this procedure I can now move forward.
Last edited:
Here is the tape I used. Thanks Dennis
3M™ Polyimide Film Electrical Tape 92
Typical Value
US units (metric)
Color Amber
Adhesive Thermosetting Silicone
Backing Thickness 1.0 mils (0,025 mm)
Overall Thickness 3.0 mils (0,076 mm)
Tensile Strength 30 lbs / inch width (53 N / 10 mm)
Elongation (% at break) 55% minimum
Electrolytic Corrosion Factor
(3M internal test method) 1.0
Adhesion to Steel 25 oz / inch width (2,8 N / 10 mm)
Comparative Tracking Index
(IEC Method 112) CTI Group IIIb
Printable Yes
Dielectric Breakdown > 7,500 V
Insulation Resistance > 1,000,000 Ohms
3M™ Polyimide Film Electrical Tape 92
Typical Value
US units (metric)
Color Amber
Adhesive Thermosetting Silicone
Backing Thickness 1.0 mils (0,025 mm)
Overall Thickness 3.0 mils (0,076 mm)
Tensile Strength 30 lbs / inch width (53 N / 10 mm)
Elongation (% at break) 55% minimum
Electrolytic Corrosion Factor
(3M internal test method) 1.0
Adhesion to Steel 25 oz / inch width (2,8 N / 10 mm)
Comparative Tracking Index
(IEC Method 112) CTI Group IIIb
Printable Yes
Dielectric Breakdown > 7,500 V
Insulation Resistance > 1,000,000 Ohms
Last edited:
- Joined
- Jan 14, 2011
- Messages
- 74,912
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
thanks
I haven't done this for a long time. Just a little repair hear and there.
I bough a dual pencil station - Weller 80 watt x2 setup for this job off Ebay ( my favorite store)
It is very helpful to get the heat when needed with two at a time and reduces overheating the component. I set one at 650 and the other at 690. Got quite good at feeding solder with one hand while holding the #2 iron. I can grap the lower temp one for smaller parts and the higher one for bigger items and both to get those jumpers and resistors glued to the backplate.
Cans are now switched from old 2n3403's
Off to cut wires
I haven't done this for a long time. Just a little repair hear and there.
I bough a dual pencil station - Weller 80 watt x2 setup for this job off Ebay ( my favorite store)
It is very helpful to get the heat when needed with two at a time and reduces overheating the component. I set one at 650 and the other at 690. Got quite good at feeding solder with one hand while holding the #2 iron. I can grap the lower temp one for smaller parts and the higher one for bigger items and both to get those jumpers and resistors glued to the backplate.
Cans are now switched from old 2n3403's
Off to cut wires