Nice work Andrew
700/1 “Tim” WOPL driver board
- Thread starter AngrySailor
- Start date
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
Huh. Probably shoulda cleaned as I went along. Hard to get atbsome stuff now... gotta get s small paint brush or something. The board almost looks worse now, just smeared dirt all around... anyone use air to blownthe alcohol off?
I use my heat gun on the no heat setting to evaporate excess alcohol off the cleaned board.
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
Huh. Just powered Tim up on a dbt then direct just to refresh my memory as to where I left off with this. I had changed the rectifier and had questionable DC offset, as Inhalf a volt. Now I’m testing it with a new meter and I’m getting 0.124v left and 0.008v right channel. Not as bad as I thought it was.
Attachments
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
I don’t see a board to amp wiring pin out for a quasi 700/1 in the instructions, does anyone have one?
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Joe has those docs...ping im...
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
my email is screwed up or you would have already have had it!!~
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Youre looking for the PL14-20 Wiring Chart..
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Yeah, the wiring coming off the PL0171 board is different than the B or 2...
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Offset is adjustable on the PL0171 board...
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
I seem to remember not being able to get reasonable offset. I think my meter was on its way out though as it crapped completely not long after. Rocking a 179 now and man is that sensitive compared to my old meter.
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Do you have a series 1 manual??
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
179 is a nice meter...good buy..
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
I think I do have the service manual yes... forgot I printed a pile of manuals... gotta find that binder think I know where it is.
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Try adjusting offset now...just for shits and giggles...
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Printed on ship paper??
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
Ships ink and binder too... shhhh
- Joined
- Jan 14, 2011
- Messages
- 75,398
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Only way to go...
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
AngrySailor
Veteran and General Yakker
- Joined
- Oct 15, 2014
- Messages
- 3,419
- Tagline
- ---not quite right
One channel 20mv the other around 100mv. Was able to get it down from almost 800mv with the level pot at min and max. My old meter was definitely fucky. Turn it on now and it reads 564mV with no leads attached. Still over spec on the offset but not as bad as I thought.
Last edited: