Newly assemble pl14 rev G bias trimmers do not work correctly

laatsch55

laatsch55

Administrator,
Staff member
#22
Joined
Jan 14, 2011
Messages
74,987
Location
Gillette, Wyo.
Tagline
Halfbiass...Electron Herder and Backass Woof
#22
Don't doubt it. I searched my shit and never found anything close....I hope i told ya that...
 
laatsch55

laatsch55

Administrator,
Staff member
#23
Joined
Jan 14, 2011
Messages
74,987
Location
Gillette, Wyo.
Tagline
Halfbiass...Electron Herder and Backass Woof
#23
CrazyIvan said:
Sorry to sound dumb, are the rail fuses the screw in fuses on the back? I never removed those. The amp was working after the DC and cap install. Does the copper bus bar between the large caps connect the caps + on bottom cap to - on top cap? I replaced the new ones the same direction the old ones came out. I did cut off the other white wire and remove from PAD5R. See pics, still -.019 on the test points. No trimmer adjustment. View attachment 66517 View attachment 66518 View attachment 66519 View attachment 66520
Click to expand...
Yep, PS caps are in right. Yes, rail fuses are the screw in type on the back.
 
MusicSteve

MusicSteve

Journeyman
#24
Joined
Mar 6, 2022
Messages
359
Location
Minnesota
Tagline
Always Thinking Outside The Box.
#24
your wiring not right , This is a Full-comp ????? I just did one and All my wires are hooked up for both boards Your PNP is not wied and is wired to the wrong spot & needs to be wired to the correct spot , you have no power for you Rt Control board 11,12
I would not hook up power yet, I will find mine wiring notes and post them
 
C

CrazyIvan

New Around These Parts
#29
Joined
Mar 27, 2022
Messages
38
#29
laatsch55 said:
Soooo...the output stage is full comp also...don't get insulted bud, just makin sure...whatcha got for outputs?
Click to expand...
I am not insulted, I am new to this. I didnt know which way to build the board, full or quasi, I chose full. Im not sure how to answer what the output stage is.
 
laatsch55

laatsch55

Administrator,
Staff member
#32
Joined
Jan 14, 2011
Messages
74,987
Location
Gillette, Wyo.
Tagline
Halfbiass...Electron Herder and Backass Woof
#32
If the amp is in quasi configuration .....Houston, we have a problem. post a pic of the outputs, so we can tell if ity's a full or quasi, I'm betting quasi...


C7 on the DCP board looks like it's in backwards as Perry has noted. A close up pic of that would be nice... too
 
WOPL Sniffer

WOPL Sniffer

Veteran and General Yakker
#33
Joined
Aug 10, 2015
Messages
11,522
Location
Minnie-Soda
Tagline
Screw it
#33
Ivan, the DCP is the board from WattsAbundant for speaker protection. Who built it? Check C7 for backwardness insertedness
 
G

George S.

Veteran and General Yakker
#36
Joined
Feb 18, 2020
Messages
5,036
#36
Ivan, you have a early 400 that was built with a quasi complementary point to point wired back wall, then the output transistors where selected and installed specifically for that quasi complementary back wall.
If you've not modified the back wall by rebuilding it full comp and installed the different output transistor configuration, then you need to build the control board quasi complementary to match it.
Also check your fuses for correct type and value. Some of these amps have had automotive fuses from the old Pontiac behind the barn or straight pieces of heavy copper wire.
Ask any question and we'll try to help. Nice job on the board!
 
You must log in or register to reply here.
Top