Derek92994's 700 Ser II White Oak conversion
- Thread starter laatsch55
- Start date
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Chaska...Somalia.....yep..
orange
Veteran and General Yakker
- Joined
- Jul 6, 2010
- Messages
- 17,704
- Tagline
- Broken beyond repair but highly affable
Those words are not in Navo's vocabulary.
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Visited the MN state fair and did some cow tipping
Been awhile since I tipped a cow ...lucky guy..
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
derek92994
Veteran and General Yakker
- Joined
- May 1, 2013
- Messages
- 7,400
- Location
- Australia
- Tagline
- Those who enter the man cave will get WOPLed
So true, are all the insides still there though?
derek92994
Veteran and General Yakker
- Joined
- May 1, 2013
- Messages
- 7,400
- Location
- Australia
- Tagline
- Those who enter the man cave will get WOPLed
That amp would have had a very hard life on the road until it met its final fate with the truck rollover.
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
The only thing I'm gonna use are the heatsinks, fuseholders, and thermoswitches....
derek92994
Veteran and General Yakker
- Joined
- May 1, 2013
- Messages
- 7,400
- Location
- Australia
- Tagline
- Those who enter the man cave will get WOPLed
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
All new Buddy....this was a fully comp amp too....are you going to want to run fans off the aux plug? Or do you have 240 volt fans?
derek92994
Veteran and General Yakker
- Joined
- May 1, 2013
- Messages
- 7,400
- Location
- Australia
- Tagline
- Those who enter the man cave will get WOPLed
To Make it easy for you, I will run the fans off an independent power supply. I'm thinking 14 blade dynamic fluid bearing aerocool fans. They push a lot of air and light up nice.
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
OK, good. That'll make it easier for you to wire up the transformer also...could you post a pic of the transformer here?? Where we can see the wiring?
derek92994
Veteran and General Yakker
- Joined
- May 1, 2013
- Messages
- 7,400
- Location
- Australia
- Tagline
- Those who enter the man cave will get WOPLed
derek92994
Veteran and General Yakker
- Joined
- May 1, 2013
- Messages
- 7,400
- Location
- Australia
- Tagline
- Those who enter the man cave will get WOPLed
My current fan configuration =)
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
derek92994
Veteran and General Yakker
- Joined
- May 1, 2013
- Messages
- 7,400
- Location
- Australia
- Tagline
- Those who enter the man cave will get WOPLed
Thanks Lee, that's only a basic fan, sucks the hot air up and out of the amp, the 9500s runs too hot to not be fan cooled, that's why it has lasted. But I will be getting some more 14 blade fans for the WOPL, they are $25 a piece.
- Joined
- Jan 14, 2011
- Messages
- 75,388
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Is that a grommet on the floor?? cause this is missing one....