phase linear 400

[Gepetto]

I suggest a nut under each of the plastic control board standoffs. Keeps those long screws secure. You also gain 1 nut width of extra spacing away from the backplanes. Should be enough thread left to use a nylon washer and nut after the control board is mounted.
Those long plastic standoffs tend to "relax".

When you order chassis, you get a longer SS screw and longer nylon standoff as well. The chassis has the room to take you higher...

 

[Gepetto]

how about this mr. george??

Nope, the gizouta and gazinta have to be tightly paired together Gene...pls look at the instructions.

 

[gene french]

The pictures on how to do it are on the website Gene. The caps hide in the shadow of the bridge rectifier as Perry states.

i found it...thank you...it is a neat item...

 

[Gepetto]

how about this mr. george??

 

[Gepetto]

Gizouta has to be paired with gazinta...every time

 

[Gepetto]

better????

better????

Yes, the 1 and 2 hole are for your AC feed to the DC Protect Board...400 only needs 1 wire, 700 needs 2 wires

 

[gene french]

Gizouta has to be paired with gazinta...every time

yes sir...just not time to get to it yet...
i will complete wiring tomorrow....about all thats lefy
thank you so much...

 

[gene french]

Yes, the 1 and 2 hole are for your AC feed to the DC Protect Board...400 only needs 1 wire, 700 needs 2 wires

the 1 and 2 hole???
dont understand...

 

[George S.]

Gene, pair your AC primary wires to and from the thermal breaker. Wasn't sure if you were going to run them across the top or the middlIe. was only commenting on your "nut' placement. Joe suggests running them across the middle.
I'm going to do it the old way across the top, then down, on my next build.

 

[George S.]

The DCP AC wires.

 

[e30m3mon]

Pad "1" or "2" on that Bridge/Snubbers board for the 400. (700 will use both pads)

 

[gene french]

Yes, the 1 and 2 hole are for your AC feed to the DC Protect Board...400 only needs 1 wire, 700 needs 2 wires

ahhh...on the rectifier

Gene, pair your AC primary wires to and from the thermal breaker. Wasn't sure if you were going to run them across the top or the middlIe. was only commenting on your "nut' placement. Joe suggests running them across the middle.
I'm going to do it the old way across the top, then down, on my next build.

yes sir...havent had time to address the wiring totally....the boards are complete...i remember how it was the last time...tomorrow i cut wires for backplanes...and run the wire for ac dcp board...
mount them up...
thank you for warching!!!
i appreciate every ounce of advice!!!

 

[gene french]

Pad "1" or "2" on that Bridge/Snubbers board for the 400. (700 will use both pads)

got it!!
takes me a while...lol
thanks sooo much...
i am less "cocky ..know it all...this build...
i feel less confident because of previous assumptions..am reading more...i think the build is better this go round...i kinda know what to expect...and i appreciate the extra eyes!!

 

[gene french]

Pad "1" or "2" on that Bridge/Snubbers board for the 400. (700 will use both pads)

logically....if i hook up both 1 and 2...i will have a 700? ?
lol

 

[e30m3mon]

logically....if i hook up both 1 and 2...i will have a 700? ?
lol

Sure .... LOL

 

[gene french]

Sure .... LOL

fascinating...
lolol

 

[e30m3mon]

DON’T GO THERE!

 

[Gepetto]

logically....if i hook up both 1 and 2...i will have a 700? ?
lol

Yes, you will have Perry's 700 Club...break out your credit card.

 

[WOPL Sniffer]

 

[WOPL Sniffer]

Gene, I don't see you this morn...... Did your electrical systems all fry???? Maybe the ruskies hit the power grid with a heat seeking moisture missile. HUH????