phase linear 400

[George S.]

Got back on the big monitor. Out 1, left backplane. Out 1 on right backplane has been unsoldered leaving a clean hole.
Out 1 is the meter signal source. No longer used because your getting your meter signals after the DCP relay with the grey and red wires.

 

[gene french]

1. isolate both yellows...
2. remove out1
3. gnd to lite board
4. disable zobel on dcp
5. reroute ac/ dc intersections...you want them up and over...

 

[George S.]

If you look at your PDF for the LED board, I THINK you need 2 meter signals wires, which you have, 2 AC wires which you have and are violet from that terminal strip, and a ground from the star ground.
This is from memory, you'll need to check and verify.
Anyhow that OUT 1 wire comes out, you've replaced it with a wire "further downstream" after the relay at DCP.

 

[gene french]

Got back on the big monitor. Out 1, left backplane. Out 1 on right backplane has been unsoldered leaving a clean hole.
Out 1 is the meter signal source. No longer used because your getting your meter signals after the DCP relay with the grey and red wires.

got it...dont i need a ground to light board??

 

[gene french]

yes...i need a ground...is labeled black on light board...i have my 8 fin open..i can easily trace down tomorrow

 

[George S.]

Post 2603. That's all for me tonight, then I'll be on phone rest of week on the road working. Hopefully the other guys with a monitor can help you. Hard to see photos well on phone. Later. Got some chores to do, then listen to a short album, then bed.

 

[gene french]

that copper plate is insulated from chassis...these gold plated jacks i got from watts came with grounding lugs...i will connect ground lugs to plate when install driver board...

 

[WOPL Sniffer]

 

[gene french]

Post 2603. That's all for me tonight, then I'll be on phone rest of week on the road working. Hopefully the other guys with a monitor can help you. Hard to see photos well on phone. Later. Got some chores to do, then listen to a short album, then bed.

thank you george...

 

[gene french]

View attachment 67299

oh ye of little faith...lol...

 

[Gepetto]

oh ye of little faith...lol...

 

[gene french]

View attachment 67301

yes sir...where do you want me to put it....
wait..wait...dont answer that...let me rephrase...
what would be a better position for the ground wire ???

 

[gene french]

yes sir...where do you want me to put it....
wait..wait...dont answer that...let me rephrase...
what would be a better position for the ground wire ???

or is it not used on back planes and be connected to driver board??
do i need to remove total wire???

 

[George S.]

Post 2582, unsolder it for now. If you need it for something else like the LED board, use it there. Night.

 

[gene french]

Post 2582, unsolder it for now. If you need it for something else like the LED board, use it there. Night.

buenas noches...dios ti bendiga...

 

[gene french]

You have a ground wire going to the RCA copper plate. The copper plate gets grounded with a wire or coax shield from the control board.
I'll stop here. That's the big stuff that jumps out at me.

understood...

 

[Gepetto]

yes sir...where do you want me to put it....
wait..wait...dont answer that...let me rephrase...
what would be a better position for the ground wire ???

Gone, gone, gone. Who told you to put that wire there? Ground loop central

 

[Gepetto]

 

[Gepetto]

I keep an assortment of small length wooden dowels handy for putting a gentle radius on the wires. The wires nest better that way and it adds a neat appearance to the wire dress.

 

[Gepetto]

Put a junk fuse in each fuseholder before soldering. It keeps the tip floating and away from the plastic while you are applying soldering iron heat.

Plug an IEC cord into the IEC receptacle when soldering to the solder lugs. Schurter did not use a very high temperature plastic for the housing. This keeps some of the soldering heat from deforming the plastic housing while soldering to the solder lugs.