Klipsch RF-7 Mark III
FREQUENCY RESPONSE
32–25kHz +/– 3dB
POWER HANDLING
250W / 1000W peak
SENSITIVITY
100 dB @ 2.83V / 1M
NOMINAL IMPEDANCE
8 ohms compatible
HIGH FREQUENCY HORN
8.5” square 90˚ x 90˚ Tractrix® Horn
HIGH FREQUENCY DRIVERS
1.75” (4.45cm) titanium diaphragm compression driver
CROSSOVER FREQUENCY
1,300 Hz
LOW FREQUENCY DRIVERS
Two 10” (25.4cm) Cerametallic cone woofers
INPUTS
Dual binding posts / bi-wire / bi-amp
ENCLOSURE TYPE
Dual chambered, bass-reflex — via dual rear-firing Tractrix ports
HEIGHT
49” (124.5cm) including plinth
WIDTH
13.875” (35.2cm) including plinth
DEPTH
17.875” (45.4cm) including plinth
WEIGHT
97 Ibs (44.1kg)
Martin Logan Motion 60XT
Frequency Response
35–25,000 Hz ± 3 dB
Dispersion
80° x 30°
High Frequency Driver
1.25” x 2.4” (3.2cm x 6.1cm)
Folded Motion XT Transducer with 4.5” x 2.75”
(11.4cm x 7cm) diaphragm.
Mid Frequency Transducer
6-1/2” (16.5cm) aluminum cone with cast polymer
basket. Sealed chamber format. Rigid structured dust
cap to reduce cone break-up modes.
Low Frequency Transducer
Two 8” (20.3cm) aluminum cone with cast
aluminum basket. Non-resonant asymmetrical
chamber format. Rigid structured dust cap to reduce
cone break-up modes.
Sensitivity 94 dB @ 2.83 volts/meter
Impedance 4 Ohms. Compatible with 4, 6, or 8 Ohm rated amplifiers.
Recommended Amplifier Power
20 – 400 watts
Crossover Frequency 400 & 2,200 Hz
Cabinet Ported
Components
Custom air core coil and low DCR steel laminate inductors.
Polypropylene film capacitors in series and low DF electrolytic capacitors in parallel. Tweeter
thermal/current protection.
Inputs
Custom 5-way bi-wire tool-less binding posts
Weight
66 lbs. (30 kg)
Dimensions
48” x 11.4” x 14.4”
FREQUENCY RESPONSE
32–25kHz +/– 3dB
POWER HANDLING
250W / 1000W peak
SENSITIVITY
100 dB @ 2.83V / 1M
NOMINAL IMPEDANCE
8 ohms compatible
HIGH FREQUENCY HORN
8.5” square 90˚ x 90˚ Tractrix® Horn
HIGH FREQUENCY DRIVERS
1.75” (4.45cm) titanium diaphragm compression driver
CROSSOVER FREQUENCY
1,300 Hz
LOW FREQUENCY DRIVERS
Two 10” (25.4cm) Cerametallic cone woofers
INPUTS
Dual binding posts / bi-wire / bi-amp
ENCLOSURE TYPE
Dual chambered, bass-reflex — via dual rear-firing Tractrix ports
HEIGHT
49” (124.5cm) including plinth
WIDTH
13.875” (35.2cm) including plinth
DEPTH
17.875” (45.4cm) including plinth
WEIGHT
97 Ibs (44.1kg)
Martin Logan Motion 60XT
Frequency Response
35–25,000 Hz ± 3 dB
Dispersion
80° x 30°
High Frequency Driver
1.25” x 2.4” (3.2cm x 6.1cm)
Folded Motion XT Transducer with 4.5” x 2.75”
(11.4cm x 7cm) diaphragm.
Mid Frequency Transducer
6-1/2” (16.5cm) aluminum cone with cast polymer
basket. Sealed chamber format. Rigid structured dust
cap to reduce cone break-up modes.
Low Frequency Transducer
Two 8” (20.3cm) aluminum cone with cast
aluminum basket. Non-resonant asymmetrical
chamber format. Rigid structured dust cap to reduce
cone break-up modes.
Sensitivity 94 dB @ 2.83 volts/meter
Impedance 4 Ohms. Compatible with 4, 6, or 8 Ohm rated amplifiers.
Recommended Amplifier Power
20 – 400 watts
Crossover Frequency 400 & 2,200 Hz
Cabinet Ported
Components
Custom air core coil and low DCR steel laminate inductors.
Polypropylene film capacitors in series and low DF electrolytic capacitors in parallel. Tweeter
thermal/current protection.
Inputs
Custom 5-way bi-wire tool-less binding posts
Weight
66 lbs. (30 kg)
Dimensions
48” x 11.4” x 14.4”