My PL400 Series 1 Rebuild

jle

New Around These Parts
Joined
Aug 17, 2024
Messages
21
Location
Rhode Island
Tagline
Older than I act, younger than I look
#1
I started a new thread as I had threatened to do, as my 1st set of postings were all about planning, research, pretending that I tidied up the workbench, and getting necessary materials together. I have an early (but not the earliest) PL400 Series 4 4-fin. I secured 8-fin heat sinks with transistor covers, the updated transformer, a new chassis, Watts Abundant's DC protection board, and all the White Oak upgrade kits.

But where do I start?! The question is related mainly to the fact that I have not found a thread where someone does a rebuild that involves a new chassis. My sense is that the general approach removes the control board, upgrades the backplane, upgrade the control board, etc. But I need to start one step earlier (with the chassis). So, here is what I think I need to do:
  • Install the transformer and heat-sink fins onto the new chassis. The need to add the other chassis hardware will become apparent as I go along (top and bottom, for example). I am assuming that the new chassis then forms the foundation for the rest of the rebuild, and gets built up with the other boards, big transistors, etc.
  • If that assumption is correct, then the next thing to go in would be the backplane boards and the gradual installation and power-up procedures for the transistors.
  • Don's instructions for the Watts Abundant board say that it gets installed first. But a comment from Don that was quoted in Nelson's thread said it goes after the backplane. So I am putting it here in the sequence.
  • Next would be the control board
  • Finally the light board
Does all that sound correct? I'll enjoy spending some relaxing time slowly and carefully building the backplane and control boards while the above plan gets corrected, tweaked and revised.

-Jon
 

George S.

Veteran and General Yakker
Joined
Feb 18, 2020
Messages
4,945
#2
Check the PDF files that Joe sent you. Joe also has a multimedia presentation on the build sequence. Maybe it's in the files.
Also look at Eric's "Hexis22" build threads. Lots of excellent photos. Look closely at how he positions the components on the boards in regards to component orientation, soldering, and wire routing.
Wire routing and dressing is critical for reliability and low noise.
Think I read every post on the forum before I built my first 400. I actually built two at the same time.
I did document my PL700Pro build here. Photos are no where as good as Eric's, but I do address some of the issues with reusing the old chassis, and they are in build sequence.
https://forums.phxaudiotape.com/threads/pl-700-pro-build.9965/
 

jle

New Around These Parts
Joined
Aug 17, 2024
Messages
21
Location
Rhode Island
Tagline
Older than I act, younger than I look
#3
Check the PDF files that Joe sent you. Joe also has a multimedia presentation on the build sequence. Maybe it's in the files. Also look at Eric's "Hexis22" build threads...
https://forums.phxaudiotape.com/threads/pl-700-pro-build.9965/
Thanks for the thoughts, George. I did those things before posting, but didn't find anything (yet) that started with a new chassis. Eric's build is humbling, or should I say "aspirational" -- I aspire to be that good with the wiring, dressing, etc. I'll keep reading (I know I have not found every build thread yet).

It just feels a little different than what I have read so far when throwing a new chassis into the mix. A "normal" rebuild would be a tear-down followed by building it back up. But I'm thinking instead that maybe I am starting with the chassis as a clean slate and building things up from there.

And of course, all of these paths remind me of "stone soup." That's were you take a clean stone, place it in a large pot with water, veggies, proteins, and seasonings. You let that simmer for a while, discard the stone and eat the soup. My original PL400 Series 1 is the stone. :)

-Jon
 

George S.

Veteran and General Yakker
Joined
Feb 18, 2020
Messages
4,945
#4
Oh, rule #1. Do not rush the build!
Hope you have the proper tools and work space.
Take your time and double and triple check everything.
You want it to power up with no issues.
Any questions, please ask, the community will help you!
 

jle

New Around These Parts
Joined
Aug 17, 2024
Messages
21
Location
Rhode Island
Tagline
Older than I act, younger than I look
#7
Hi Jon
I sent you, amongst the many, many files one called Complete Rebuild Slide Show.docx. Look for that
(Jon smacks is palm against his forehead...) Joe, I had looked at that file, but in retrospect I was so focused on the boards, wires, etc., that I totally missed the fact that the slideshow is a precise answer to my very question. And it confirms my view of building on that foundation. I need to add "install big f'ing capacitors" to the project plan list.
 

Hexis22

Chief Journeyman
Joined
Dec 28, 2022
Messages
639
Location
Wisconsin
#9
Save your back and hold off on the transformer install and sink install till you get the backplane boards in.
Agree, complete the backplane board and control board assembly, then progress to chassis assembly. Transformer gets installed after securing the backplane boards and heat sinks.

Most of my build threads follow this sequence for a new chassis build. I’ve only built one amp with the original chassis, my first amp build, and ALL others with a new chassis.
 

WOPL Sniffer

Veteran and General Yakker
Joined
Aug 10, 2015
Messages
11,522
Location
Minnie-Soda
Tagline
Screw it
#10
Agree, complete the backplane board and control board assembly, then progress to chassis assembly. Transformer gets installed after securing the backplane boards and heat sinks.

Most of my build threads follow this sequence for a new chassis build. I’ve only built one amp with the original chassis, my first amp build, and ALL others with a new chassis.

Gotta have the White Oak chassis. More room and they are kick ass. Yeah, it's not often I use an original chassis. Matter of fact, I'm going to carry the old Pro 700 (a series II ) chassis and heat sinks next door and put them in Paul's metal recycle pile.
 
Top