Stephens Phase Linear 400--In for the works.
- Thread starter laatsch55
- Start date
Uh-oh. Now you've done it! Maybe you'll find the name there.
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Getting closer. Gonna see if an outboard power supply in a toroid version is going to lower the noise floor.
Cool. So what Volt Amp rating and rail voltage are you going with? This sounds like a fun experiment.
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Those Holden and Fischers I've got. Don't know the VA rating, rectified +/- voltages are 92.3 DC.
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
If the hand slips-----DINNER IS SERVED!!!!
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
wELL, i WAS TORN between sex and food, ya know how that goes...
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
Beins the heat sinks are where we start with Joe's backplane boards, I shut down when the copper arriveed to do the heatsinks. I taped as much as I could as soon as I unwrapped it. Just running your hand accross it.
Also, I had proposed to Steve that for critical listening ( IE-NOT mach 8) that I could add a couple positive speaker posts in a bypass situation. The RCA in holes are now occupied by the bypass posts. The new RCA in's will be located above and below the bottom standoff for the board mount.
Also, I had proposed to Steve that for critical listening ( IE-NOT mach 8) that I could add a couple positive speaker posts in a bypass situation. The RCA in holes are now occupied by the bypass posts. The new RCA in's will be located above and below the bottom standoff for the board mount.
Attachments
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
With a hand slip you've got both!
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
DAYAM if you aint right!!
The jacks look first rate - will these solder directly to the backplane board?
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
No, but the shielded pair won't be but 3" long.....
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
I don't think Joe is into Ghirardelli's anymore, probably onto bigger and better, don't know what that would be though, these folks been at it quite awhile.
The storm has hit. Got a couple wells to check then wait for the pumpers to call in with all theit problems. There will be very few, or a lot. Seems to be the way it works.
The storm has hit. Got a couple wells to check then wait for the pumpers to call in with all theit problems. There will be very few, or a lot. Seems to be the way it works.
I never get tired of Ghiradelli's Lee, excellent chocolate. Was wondering what teaser Dennis was talking about
- Joined
- Jan 14, 2011
- Messages
- 75,523
- Location
- Gillette, Wyo.
- Tagline
- Halfbiass...Electron Herder and Backass Woof
The chocolate appears prominately in both pics, so I assumed it was that. Nothing else in the pics I could see would be a Joe teaser.