Search results

I just received my Tape repair Kit. Its a 1/8" w bar and Slicing Tape, I hope it works better than no bar and 1/4" tape. I also finally found a CLEAR Leader tape :D I been looking for a long time. I'm installing a NOS different Head which I hope will help w Ailment.

Good Input I also been looking into different tapes, I like The Maxell's and I heard they are still good over time and the older Type 2 have lost a little. The Sony also are really good and some of them really run smooth w less noise . Some of the TDK have not been good over time. The TDK "D"...

Thanks Joe , what do you think of that circuit for the Wima , I'm also thinking of the changing the other ones to wima that are not in the updates and make them all the same kind and are listed in the bottom of the BOM I feel a lot better now !;)

I'm installing a NOS ALPS Ferrite Head, That I bought from Alex from A.N.T The new head needs some modification which I have a PDF file and Thanks you Alex Nikitin 20 October 2017 PDF file for this. but no BOM, so I'm Making all the documentation for this update . The drawings is not the...

I tries to find one and as far as I know Their is no schematic for both motors after weeks of looking , I tried to make one but the board appears to have hidden parts in the middle of it and gave up. Thiers all kinds of YouTube video and forums, how to clean and rebuild them Xraytony has a video...

Wow to be Organizes I need more room which I don't have, All I know is it takes a lot of tools and Hardware and Parts to do anything and after your done its time to just put it in a small and big bins, and think I will deal w it later than you have a bunch of bins and I ask my self how did I get...

I don't like the seal plastic case, I seen on YouTube People drilling them out. I also seen the rollers inside the tape wobbling to much , wondering in I should out some grease on them, do they make updated rollers? Also I just remembered, Like you said and Cars,,, and what a bad place for...

I think the time is buy is now that the market is flooded? I think FB is a good places to buy and you can get a better deal. I just picked up 24 Maxwell UR 90 all sealed for $25.00 that night, I Like the clear tapes for testing and they look cool. I also bought some Maxell XLII off E-bay for...

Thanks, The more options the better Anyone have a replacement for the Original one?

Looks Cool Did you buy new Volume Knob? if yes do you have a part Number? thanks Steve

Mark Here is what I use, you can pm me If the Nut is not Adjusted correctly the tape will curl up. Need a clear tape to see it and manaul pull th head up I also cut the plasic to see better. I since bought a Tool for this. Also I have tried the Bigger pully this week it seemed to not help (I...

Mark The Nylon Nut will strip out because they put to much glue on them. I stripped out some before knowing to try to remove the Glue. if you need a Nut I bought Some, I also Have some Pitch roller since I also Rebuilding some Pioneer CT-F Now. They are not the easiest to figure out. The idler...

I think he will have a hard time selling it , now that its cold. Its a very buzzy place in the summer time and high class in some spots and they have higher taxes in that area.

Ok Good Luck , is that a good price? to make it worth it? Thanks Steve

Lee do you know the address and zip code, could be a address close by. Its not close could be 2 to 3 hours one way.

Update 400 II Same results if I ground the transformer the .2vac goes even lower. Check 120vac N and Hot (is correct) Check all winding All wires were not Shorted to Ground -None Winding - all Ohm out (None shorted) all Secondary Winding to Primary - Open George, Joe , I guess it ok? Note -...

and JB weld? I saw in your post some were? I like the bigger bolts :)

Thanks George ;) A- I will check again. I see the AC Ground wire was hooked up to the Case frame which grounds the Transformer ? I did not do these step. 1- I will have to check my AC is correct first (Check my cord and w a ac power tester also going to a my main power strips and my test power...

Thanks I'm working on the 400II transformer now. I did the voltage test for Hot and N (which is a different transformer can be 120vac or 220vac ) and it worked great. It was .2vac and 6vac this is a vary good test to use before soldering to IEC Male Connector. It ended up like I thought it would...

Good to Known, Thanks for posting this. Looks Like a better way to do it than switching the 2-Prong cord around. and knowing this before adding 3-Prong Plug. Will have to try this for the 400II and 700II. I see in your transformer bolts- did you order SS and what size and length worked?