PL 400 series 1

GMEAD

New Around These Parts
Joined
Apr 20, 2024
Messages
11
#1
I recently bought some PL amps at an estate sale. One of which is what I believe to be 400 series 1 (4 fins). It works perfectly with the exception of dim lighting on the VUs. Of course after doing some reading I'm a little concerned for my speakers. It's very clean inside and may have new caps and a new looking board. Could you please identify the board and tell me if this amp has been upgraded sufficiently to trust to run my speakers without burning up the drivers that are no longer available?
 

Attachments

62vauxhall

Veteran and General Yakker
Joined
May 14, 2014
Messages
2,321
Location
Southwest Kootenays BC
Tagline
No such things as bad days, just bad moments
#2
I have a 4 fin 400 which has darkly tinted meter lenses. Dark enough so that without directly viewing the original incandescent bulb filaments, I could not tell that they were lit. Bright white LEDs on a White Oak lightboard overcame the dark tint.

Is that a date stamp on the top left corner of your board?
 

mlucitt

Veteran and General Yakker
Joined
Jun 24, 2011
Messages
3,469
Location
Jacksonville, FL
#3
You are in dangerous original/unmodified equipment territory. The board and the amplifier are very clean, but are all original and likely 45 years old.
At a minimum, you should add a DC Protection Relay/Delay Board to protect your speakers. It is cheap insurance. You can install it yourself if you are handy with a soldering iron. Or, some of the techs on this Forum can do it for you.

Where are you?
 

GMEAD

New Around These Parts
Joined
Apr 20, 2024
Messages
11
#4
You are in dangerous original/unmodified equipment territory. The board and the amplifier are very clean, but are all original and likely 45 years old.
At a minimum, you should add a DC Protection Relay/Delay Board to protect your speakers. It is cheap insurance. You can install it yourself if you are handy with a soldering iron. Or, some of the techs on this Forum can do it for you.

Where are you?
I'm in Western Washington. I have a guy that can fix anything and he's affordable. I was thinking of getting the Dual Mono board kit from White Oak as that's supposed to be the cure all so I think I'll probably order that and a light kit and leave it unplugged until it's installed. Thanks for the ID on that board.
 

GMEAD

New Around These Parts
Joined
Apr 20, 2024
Messages
11
#5
I'm in Western Washington. I have a guy that can fix anything and he's affordable. I was thinking of getting the Dual Mono board kit from White Oak as that's supposed to be the cure all so I think I'll probably order that and a light kit and leave it unplugged until it's installed. Thanks for the ID on that board.
You are in dangerous original/unmodified equipment territory. The board and the amplifier are very clean, but are all original and likely 45 years old.
At a minimum, you should add a DC Protection Relay/Delay Board to protect your speakers. It is cheap insurance. You can install it yourself if you are handy with a soldering iron. Or, some of the techs on this Forum can do it for you.

Where are you?
So are the DC Protection boards available from source's other than White Oak? I seem to be having a communication challenge with them.
 

GMEAD

New Around These Parts
Joined
Apr 20, 2024
Messages
11
#8
They just took a lot longer to respond to my email than I expected. All is well now.
 

Gepetto

Administrator
Staff member
Joined
May 15, 2011
Messages
13,944
Location
Sterling, MA
Tagline
Old 'Arn Enthusiast
#10
They just took a lot longer to respond to my email than I expected. All is well now.
Hi Greg, I try to be very prompt but my day job and government get in the way very often. And we are in peak season for the government activities as we are 1 week away from annual town meeting...
 

GMEAD

New Around These Parts
Joined
Apr 20, 2024
Messages
11
#11
Hi Greg, I try to be very prompt but my day job and government get in the way very often. And we are in peak season for the government activities as we are 1 week away from annual town meeting...
Those pesky day jobs. I understand. No worries. Actually the extra couple days gave me a lot better understanding on where to start this process.
 

wattsabundant

Chief Journeyman
Joined
Apr 26, 2011
Messages
932
Location
Central Ohio
#12
Those pesky day jobs. I understand. No worries. Actually the extra couple days gave me a lot better understanding on where to start this process.
.

A week ago, I got off a nine day cruise in the Caribbean. I made it a point to be off-line. I didn’t want to let the world know the house was empty. It can be a struggle to keep up with everything. I went straight from the cruise ship to my Houston office and started a class next day. I try to keep stock at the Houston office, where I average over 100 nights year. Retirement is looming later this year. No doubt that will free up some time to catch up.
 

mlucitt

Veteran and General Yakker
Joined
Jun 24, 2011
Messages
3,469
Location
Jacksonville, FL
#14
Retirement is looming later this year. No doubt that will free up some time to catch up.
Ha! When you retire, you are working for a new boss, and that guy is a pain in the ass.
 
Top