Search results

Thanks Guys, I appreciate the kind words. Looks like I won't be jamming tonight. I have to do some wire rework to do. The B- to the Left Cylon meter came up a little short. Gotta run some new. Here's some more pics....Thanks for looking

Well Guys, It's been a Wonderful day.. 4th Row installed, Powered up with DC ground,10K jumpers removed, No Smoke, No Shorts, No Blown Fuses, 0v Outputs. All voltages good. Bias set. Thanks for looking..... Left Channel Bias Right Channel Bias

That's sorta what I figured. I didn't mess with it. I won't be too far behind Lee, I tend to push the Polks pretty hard sometimes....:D

Moving right along.....3rd row installed and tested. All test were good. No issues. I would have written it all out like before but, Y'all already know what the Tests consist of. I've got row 4 waiting :p. Thanks for looking...... Thanks Guys for the words of encouragement..... ...

Finished install and Testing of the 2nd row of Transistors. No Shorts, Blown fuses, Smoke, Shorts to Transistor Cans, Voltage present at B+/B- rails, 0 volts at R/L outputs, All pad voltage close to safe mode bring up chart, Checked Bias, hanging around 0.348v still in the perimeter. Thanks for...

Yes Sir, I made one before starting the build, as per the Instructions. Mine doesn't look quite as sexy as yours. I didn't even think about shrinking it I like it..... I'll have to do some modification...Thank you for the Pic.

I do appreciate the guidance and help answering my questions It sure made everything more clearer for me. Learning all the time....I like it. Thanks Guys. Rockin' On.......:D

Thanks Mark I intend to straighten the wiring after the Transistors are installed, and all test are good. I left them alone, Just in case I had to remove Control Board..

Got a question before I install 2nd row of Transistors. Is it normal for the caps to discharge at this stage of the build? Reading a few minutes after powering down....

Got the Bias set also.... 0.350v Left Channel Right Channel Thanks for looking......

Cool, Thanks Joe

Control Board installed....No Shorts, No blown fuses, No Smoke, No shorts to Transistor Cans, Voltage present at B+/B- rails also, All pad voltage close to safe mode bring up chart, 0 volts at R/L outputs. Noticed a drop in voltage. I take that as being normal, Due to installation of the...

Bottom row installed....... Initial Test..... No Shorts from DC ground or B+/B- rails, No shorts to Transistor Cans Power bring up with 10k jumpers ....No Shorts, No blown fuses, No Smoke, Voltage present at B+/B- rails also, pads 11&12, 0 volts at R/L outputs. I'm at #21 on the...

Thank You, For kind words Sir. With all the good reviews on these Amps after the WOPL builds, I'm pretty sure I'll Love....Right now, Just hoping this things gonna work when I get it done. If everything goes well this build, I have a couple of 700 ll's, Planning to do the Full WOPL treatment...

Thank You, Sir ROCKIN' ON.......................Slooooooooly

Brought up the Bare Wire Chassis today.... No smoke, No shorts and no blown fuses. Is the voltage reading about right at this stage in the build? Thanks Guys

Deep Purple.... Made in Japan

Thanks Joe, That sure helped a lot. I see it now. Looked at the holes in the heatsinks and I can see the offset. Like I said, don't know anything about the Output Transistors. I'll take my time and keep referring to the Backwall Diagram you sent. I even see the offset in the Diagram now.

I've got a few questions on the Output Transistors. Never done any kind of work with them. How do you tell the correct orientation? I noticed when I took one out to look at it, There was an arrow molded in the styrofoam. Is that pointing the correct orientation?

Ground lugs arrived today. Finished the wiring on the caps, Tested for shorts....No problems, Everything's looking good.