Search results

  1. Pulpmillguy

    And the journey begins...

    Bingo! The quasi threw me...
  2. Pulpmillguy

    And the journey begins...

    Joe, I still haven't found this BOM that you refer to...and is there some sort of narrative that goes along with the assembly slide show?
  3. Pulpmillguy

    And the journey begins...

    I wish I could say that I left those unsoldered on purpose to see if anybody was really looking and you won the prize for attention to detail but damn, good catch! (you get the prize for attention to detail anyway!!!) You are right, I put all of the test points in and only soldered "most" of...
  4. Pulpmillguy

    And the journey begins...

    I was just copying what was shown in the recommended assembly instructions I got from Joe. I did it partially so I would put a little distance from the solder joint to the device...I tend to err on the cautious side
  5. Pulpmillguy

    And the journey begins...

    I was thinking about easing the heat sinks on with a pair of curved needle nose pliers so I don't put any undue compressive forces on the leads
  6. Pulpmillguy

    And the journey begins...

    Like they say down in the deep south where I am from "hold my beer and watch this..." But I hope that I have a relatively smooth journey but I know there will be some bumps in the road along the way. Some notes from today's progress. Continued assembling the control board and when I got...
  7. Pulpmillguy

    And the journey begins...

    Oh don't worry, I plan to take lots of pictures. Don't hold back on your comments, I'm a tough old geezer and can take it (but I want/need to know when I am fucking up!) Looking forward to a wonderful project.
  8. Pulpmillguy

    And the journey begins...

    OK guys, parts came in yesterday (thanks, Joe) and I have sorted/organized the goodies and am starting to melt lead... Now I really can't wait to hear that bad-boy again!
  9. Pulpmillguy

    Funny pictures...

  10. Pulpmillguy

    Funny pictures...

  11. Pulpmillguy

    Funny pictures...

  12. Pulpmillguy

    Funny pictures...

  13. Pulpmillguy

    Funny pictures...

    The only Goddamn problem is it's the truth...
  14. Pulpmillguy

    Funny pictures...

    THE best...
  15. Pulpmillguy

    Funny pictures...

  16. Pulpmillguy

    Phase liner PSU

    Actually most small motors are single phase and only big loads like the stove top are wired up 3 phase. All big shop tools over 3 kw are 3 phase. The electric heat has a separate 240 control circuit and then a separate 3 phase supply for the heaters...but each heater is only single phase.
  17. Pulpmillguy

    Happy Birthday MB1953

    Happy Birthday! Hope you hear this loud and clear...
  18. Pulpmillguy

    Happy Birthday Jerry

    Belated Happy...hope it was a great one (if you can remember it :wav:)
  19. Pulpmillguy

    Phase liner PSU

    OK, Mr. Smarty Pants :D...it was a nominal 240V and 400V that I was talking about. Just got back from the shop to verify but here is what I currently have: Phase 1 238,0 v Phase 2 237,1 v Phase 3 237,2 v 1-2 411,5 v 2-3 411,6 v 1-3 411,6 v And yes...
  20. Pulpmillguy

    Phase liner PSU

    the panel has all 3 phases and a common neutral so you get three (3) 240v legs. If you wanted to wire then together delta then you get 400v phase to phase but WYE you get 240v. Like one comment..."less copper"...most of the wiring in the house is 1,5mm2 for a 16A circuit.
Back
Top