Search results

I got the Cylons calibrated today. Test drove it a minute or Two on the bench, Sounded alright. You can't expect a whole lot through a pair of Maximus 7's. I'm just happy it made Music. I'll put it in the system after I get Sherri put back together. Then I'll let you know if I done good...

Found it, Thanks Joe

Hey Guys, Would someone Please educate me on calibrating these meters. I'm not real clear on how to set them. Thank you

Just some old microphone cable I had laying around..... Figured I'd try it out

I'll ask Bob in September, See how he likes it. :D

Meter Boards wired up. Need calibrating. i will try sometime tomorrow to finish it up. Thanks for looking Powered up with dim bulb, no issues A little peek inside....

Thanks Guys, I appreciate the kind words. Looks like I won't be jamming tonight. I have to do some wire rework to do. The B- to the Left Cylon meter came up a little short. Gotta run some new. Here's some more pics....Thanks for looking

Well Guys, It's been a Wonderful day.. 4th Row installed, Powered up with DC ground,10K jumpers removed, No Smoke, No Shorts, No Blown Fuses, 0v Outputs. All voltages good. Bias set. Thanks for looking..... Left Channel Bias Right Channel Bias

That's sorta what I figured. I didn't mess with it. I won't be too far behind Lee, I tend to push the Polks pretty hard sometimes....:D

Moving right along.....3rd row installed and tested. All test were good. No issues. I would have written it all out like before but, Y'all already know what the Tests consist of. I've got row 4 waiting :p. Thanks for looking...... Thanks Guys for the words of encouragement..... ...

Finished install and Testing of the 2nd row of Transistors. No Shorts, Blown fuses, Smoke, Shorts to Transistor Cans, Voltage present at B+/B- rails, 0 volts at R/L outputs, All pad voltage close to safe mode bring up chart, Checked Bias, hanging around 0.348v still in the perimeter. Thanks for...

Yes Sir, I made one before starting the build, as per the Instructions. Mine doesn't look quite as sexy as yours. I didn't even think about shrinking it I like it..... I'll have to do some modification...Thank you for the Pic.

I do appreciate the guidance and help answering my questions It sure made everything more clearer for me. Learning all the time....I like it. Thanks Guys. Rockin' On.......:D

Thanks Mark I intend to straighten the wiring after the Transistors are installed, and all test are good. I left them alone, Just in case I had to remove Control Board..

Got a question before I install 2nd row of Transistors. Is it normal for the caps to discharge at this stage of the build? Reading a few minutes after powering down....

Got the Bias set also.... 0.350v Left Channel Right Channel Thanks for looking......

Cool, Thanks Joe

Control Board installed....No Shorts, No blown fuses, No Smoke, No shorts to Transistor Cans, Voltage present at B+/B- rails also, All pad voltage close to safe mode bring up chart, 0 volts at R/L outputs. Noticed a drop in voltage. I take that as being normal, Due to installation of the...

Bottom row installed....... Initial Test..... No Shorts from DC ground or B+/B- rails, No shorts to Transistor Cans Power bring up with 10k jumpers ....No Shorts, No blown fuses, No Smoke, Voltage present at B+/B- rails also, pads 11&12, 0 volts at R/L outputs. I'm at #21 on the...

Thank You, For kind words Sir. With all the good reviews on these Amps after the WOPL builds, I'm pretty sure I'll Love....Right now, Just hoping this things gonna work when I get it done. If everything goes well this build, I have a couple of 700 ll's, Planning to do the Full WOPL treatment...