Recent content by audiobob

  1. audiobob

    700B on Craigslist if anyone is interested

    Found this on Craigslist in Seattle for $550.00. The following is what is in the post if anyone is interested: http://seattle.craigslist.org/see/ele/5145123267.html Re-posted due to "buyer" flaking and not showing---gave him THREE chances to get here and now he wants "just a few more...
  2. audiobob

    Bob's 4 WOPL 400 builds

    Thanks Lee. I'll probably talk to Don about it and see what he thinks.
  3. audiobob

    Bob's 4 WOPL 400 builds

    I looked at a few and finally decided on this one. It's made by Aavid Thermalloy 579103B00000G ( Digi-Key # HS236-ND). My other 3 PL400s don't have the extra fins so I'm hoping these will comp for that. Just an extra precaution. I may want to drive them a lot harder in the future.
  4. audiobob

    Bob's 4 WOPL 400 builds

    Thanks Joe. If those who have a good ear for audio but haven't heard a WOPL could hear one, I think there would be a real scramble to get there hands on one. Very nice!
  5. audiobob

    Bob's 4 WOPL 400 builds

    Thanks Fred.
  6. audiobob

    Bob's 4 WOPL 400 builds

    So cycling the power did reset it. Was listening at an even lower volume ( maybe 25% volume ) last night and it did it again after about an hour. Cycled power and no problem with for the last 3 hours of play at a little more volume than that. Is there maybe a mod for the DC Protect board? I...
  7. audiobob

    Bob's 4 WOPL 400 builds

    Finally got the first one done. This thing sounded great last night. Indeed no hiss or any sound coming from the speakers at full volume. I had my Anthem D1 hooked up for the preamp and gave a listen to Allen Parson's Project Turn of a Friendly card and David Templton's Never in a lifetime as...
  8. audiobob

    Bob's 4 WOPL 400 builds

    Well that was it. I some how flew right over R36 in the BOM and on the package of 1 ohm 1/4 watt resistors during the build. In stalled the resistors in R36 and was able to adjust both. Thanks again Lee. Can't wait to hear this one tomorrow.
  9. audiobob

    Bob's 4 WOPL 400 builds

    I'll find a 1 ohm resistor for R36 and give it another try.
  10. audiobob

    Bob's 4 WOPL 400 builds

    Yes, R38 has a jumper.
  11. audiobob

    Bob's 4 WOPL 400 builds

    Thanks Lee. I thought it fit right in here. Say, I seem to have a problem with my bias adjustments. I have 6mV on the left and 22mV on the right bias test points to the input minus per the procedure and those numbers don't change when adjusting the pots full range. I can't seem to figure...
  12. audiobob

    Phase Linear (Magazine Reviews, Articles, Etc.)

    Very interesting indeed.
  13. audiobob

    Bob's 4 WOPL 400 builds

    Actually connected the OUT2 L and R with a 10K each to the two white wires that go to the common chassis ground. My problem I think was that I was using crapy alligator leads that probably gave me more than 10K of resistance. The only thing I did was replace the alligators with the hardwire...
  14. audiobob

    Bob's 4 WOPL 400 builds

    Success! Got rid of the alligator leads and hooked up to a terminal block and I never went over a millivolt when bringing it up. The alligator clips were cheepees and may not have given very good connections. Caps to 80V + and - with no problems observed. Now to finish the build.
  15. audiobob

    Bob's 4 WOPL 400 builds

    Hi Joe, yes I connected the 10K resistors, one each to each channel, with nothing connected to the DC output board except for a couple grounds. The resistors are connected via alligator clip leads. I'm going to try using a small contact block and see if that helps.
Top