• 62vauxhall's Avatar
    Yesterday, 01:04 AM
    Had not in been in this particular store for a couple of weeks - the LP selection had gotten pretty stale. This record may have been passed over by...
    16764 replies | 986092 view(s)
  • 62vauxhall's Avatar
    01-14-2018, 03:11 AM
    Speakerlabfan, looks like you've been dragging an M93E a fair bit. So have I on a Zero 100 and that combo's been getting the most use lately. I'm...
    16764 replies | 986092 view(s)
  • 62vauxhall's Avatar
    01-11-2018, 10:15 PM
    Some Yamaha's (and others) had "direct" switches. When engaged, tone and balance controls were bypassed.
    111 replies | 1918 view(s)
  • 62vauxhall's Avatar
    12-24-2017, 02:41 AM
    If you need or like a lot of inputs, an original series I Apt Holman is hard to beat. And if turntables are your thing, it was created with them in...
    111 replies | 1918 view(s)
  • 62vauxhall's Avatar
    12-24-2017, 02:05 AM
    62vauxhall replied to a thread Long shaft pot in General DIY
    Yup, CAD - at Lordco. It was $11 at Canadian Tire (checked their website) but since I was passing a Lordco on my way to a job, ducked in and got...
    13 replies | 271 view(s)
  • 62vauxhall's Avatar
    12-24-2017, 12:04 AM
    62vauxhall replied to a thread Long shaft pot in General DIY
    Just put that DBX 3BX SD back together, ran it for a while and it works like a hot damn. Thanks for the JB Weld endorsements. I got some...
    13 replies | 271 view(s)
  • 62vauxhall's Avatar
    12-23-2017, 03:07 AM
    Those are some nasty good looking amps you cobble together.
    26 replies | 742 view(s)
  • 62vauxhall's Avatar
    12-22-2017, 12:25 PM
    62vauxhall replied to a thread Long shaft pot in General DIY
    Yah, that's crazy expensive and made more so by the US/CA currency difference. I actually did see that pot. The reply I got back from Harman/DBX...
    13 replies | 271 view(s)
  • 62vauxhall's Avatar
    12-22-2017, 02:21 AM
    62vauxhall replied to a thread Long shaft pot in General DIY
    I was trying to find out if JB Weld would work in a situation like this. I'm going to assume the shaft of the old pot is aluminum as it is not...
    13 replies | 271 view(s)
  • 62vauxhall's Avatar
    12-21-2017, 02:51 AM
    62vauxhall started a thread Long shaft pot in General DIY
    I've been mulling over ideas for a replacement potentiometer to replace one where the shaft came out. I took the old one apart and thought I fixed...
    13 replies | 271 view(s)
  • 62vauxhall's Avatar
    12-19-2017, 01:21 AM
    Hey, you're back! What did you finally end up with for a pre-amp?
    19 replies | 766 view(s)
No More Results
About 62vauxhall

Basic Information

About 62vauxhall
Location:
Greater Vancouver Area. BC
Tagline:
No such things as bad days, just bad moments

Statistics


Total Posts
Total Posts
1,292
Posts Per Day
0.96
General Information
Last Activity
Today 12:37 PM
Join Date
05-14-2014
Referrals
0